RUMCars Forum
General Category => Unusual Microcar Discussion => Topic started by: tibo on October 06, 2014, 08:55:39 am
-
hi to all!
I found a new isetta BMW 300 RHD in France! but this time , there is alot of work in auto body . would you have some good places to order parts at great price ? ( steel parts )
I'm in the south of France and I have often improter parts from other countries ..
if you know a shop with attractive price ???
-
I tend to get my Isetta parts from these people
http://www.oldtimerteile.net/showgroup.php?id=6_BMW-Isetta---Fahrgestell#.VDJN_LdOWic
There is the Isetta owners club of GB part department and also The Bromley Bubble company but nobody is selling the parts cheap.
Its strange that with so many LHD cars produced around the world that a RHD car turns up in France! ;D Hope you find what you need.
-
Doesn't look too bad bodywork wise, usual areas around the front wings. Floor good? They didn't slap too much paint there and the rust tends to form between the ribs and the bitumen sound deadener, the front part usually goes first.
Not tried these people, but their panels look okay in the pictures, and they do a pretty extensive range.
http://www.cascu.co.uk/isetta.htm
-
And I believe spends part of his time in France, though up north, I think, AndyL. Might be handy?
-
I usually buy at "oldtimertiele" they are fine, but the steel parts are very expensive ... I think the car is not very big yet ...
in terms of the car , the body is completely bloody ..
I need a new door and all the floors are down.
during the return trip the counterweight crossed the floor ...
but it was complete and in France ... so I will not quibble !
isetta this going to help me rebuild my first isetta (purchased already dismounted ... )
-
Yes tibo most of us have card that are "not very big yet " ;D you are in the right place
-
Hi Tibo,
Try Jim Hacking Junior at http://www.micro-car.net/index.php/2/ (http://www.micro-car.net/index.php/2/)
All panels are made in house and are of high quality. Contact young Jim via : jim@1offsheetmetal.com
I am sure I recognise your Isetta and if it's the one that I think it is then you have a very special car which needs to be restored to a high standard.
Grant
-
yes it's Mr marchal one , a very nice storry !...
humans have only one life, cars have several !
I hope to keep this car for a living too!
-
They only sell floors and door bottom repairs though don't they?
The floopans look very expensive, basically £500 with the VAT. A new new floor from Germany is half that. I believe Jim's floors are galvanized, but it still seems a high premium.
Another company that does panels is Radford. Thes were recommended by the IOC, and I expect they produce the repair sections available through the club spares scheme.
http://www.radfordpanel.co.uk/isseta.htm
-
well i hope Radfords can make a good Isetta floor - cos they can't even spell ISETTA in that link !!
-
I noticed that. :)
Correctly spelt on the page itself, however.
-
yes i did see but really !! :)
-
I will have a look on germany, shopping in UK for a floor ... could be very very expressive ...
-
These chaps do what looks like a very nice floor at 239 euro (not sure if that includes tax). However i don't know if they do a RHD floor.
http://isetta-service.de/shop.php?cat=1§6
They supply sweeties with the bits! :D
-
Tibo,
I have been talking to Tony Marshall and realise the Isetta you are setting out to restore once was the very proud possession of Lynne Marshall. It should be on the Register, ask Alastair to check. Anyway I am sure once the 'gang' know which car it is, its restoration will be followed avidly. All the very best. Jean
-
hi to all!
I found a new isetta BMW 300 RHD in France! but this time , there is alot of work in auto body . would you have some good places to order parts at great price ? ( steel parts )
I'm in the south of France and I have often improter parts from other countries ..
if you know a shop with attractive price ???
Nice project , I found this interesting catalog:
http://www.gtsadler.dk/Isetta%20Partkatalog%20UK.pdf